

It is currently Wed May 22, 2019 8:40 am

View unanswered posts  View active topics
Tell a friend!

Page 1 of 1

[ 3 posts ] 

BAD TERMINATION OF ONE OF YOUR APPLICATION PROCESSES
Author 
Message 
identaton
Joined: Wed Aug 01, 2018 7:00 am Posts: 11
University: Zhejiang University

BAD TERMINATION OF ONE OF YOUR APPLICATION PROCESSES
Hello! I am testing the calculations by EPW. The problems is like below, when doing the procedure "Solve anisotropic Eliashberg equations on imaginaryaxis", it output like "BAD TERMINATION OF ONE OF YOUR APPLICATION PROCESSES". I also try changing the etf_mem from 0 to 2, it does not work. Can anyone give me any suggestions? Thanks a lot. _________ intel18+mkl18+impi, etf_mem=0 give the following output:
temp( 1) = 0.0005 K Solve anisotropic Eliashberg equations on imaginaryaxis Total number of frequency points nsiw ( 1 ) = ****** Cutoff frequency wscut = 1.0000
=================================================================================== = BAD TERMINATION OF ONE OF YOUR APPLICATION PROCESSES = PID 13981 RUNNING AT compute1511 = EXIT CODE: 9 = CLEANING UP REMAINING PROCESSES = YOU CAN IGNORE THE BELOW CLEANUP MESSAGES ===================================================================================
_____ when using intel12+mkl12+openmpi, the output is: temp( 1) = 0.0005 K Solve anisotropic Eliashberg equations on imaginaryaxis Total number of frequency points nsiw ( 1 ) = ****** Cutoff frequency wscut = 1.0000 4 total processes killed (some possibly by mpirun during cleanup)
__________ by playing with some input parameters, I now get the following message from the output: Total number of frequency points nsiw ( 1 ) = 184691 Cutoff frequency wscut = 1.0000
Size of required memory per pool : ~= 5.7537 Gb
AKeri is calculated on the fly since its size exceedes max_memlt
The pbs jobs are still there, but the calulations was stuck without updating; I also tried to give max_memlt with bigger values (>5.8 Gb), but the calculations then give "= BAD TERMINATION OF ONE OF YOUR APPLICATION PROCESSES" again. I will appreciate it very much if someone can help me fix the problem.

Thu Aug 09, 2018 5:37 pm 


roxana
Joined: Fri Jan 22, 2016 6:48 pm Posts: 111
University: SUNYBinghamton

Re: BAD TERMINATION OF ONE OF YOUR APPLICATION PROCESSES
Hi,
I believe the code is crashing because the input temperature at which the anisotropic Eliashberg equations need to be solved is very small (0.0005 K) and then the number of imaginary frequency points nsiw is very large (it this case more than one million since it is printed as ****).
WRITE(stdout,'(5x,a,i6,a,i6)') 'Total number of frequency points nsiw ( ', itemp, ' ) = ', nsiw(itemp)
The equations should be solved in the vicinity of 0 K, but I wouldn't go below 1 K. You may also want to reduce wscut. What is the estimated critical temperature with McMillan formula in your case?
Best, Roxana
_________________ Roxana Margine Assistant Professor Department of Physics, Applied Physics and Astronomy Binghamton University, State University of New York PO Box 6000 Binghamton, NY 139026000

Wed Aug 15, 2018 7:25 pm 


identaton
Joined: Wed Aug 01, 2018 7:00 am Posts: 11
University: Zhejiang University

Re: BAD TERMINATION OF ONE OF YOUR APPLICATION PROCESSES
roxana wrote: Hi,
I believe the code is crashing because the input temperature at which the anisotropic Eliashberg equations need to be solved is very small (0.0005 K) and then the number of imaginary frequency points nsiw is very large (it this case more than one million since it is printed as ****).
WRITE(stdout,'(5x,a,i6,a,i6)') 'Total number of frequency points nsiw ( ', itemp, ' ) = ', nsiw(itemp)
The equations should be solved in the vicinity of 0 K, but I wouldn't go below 1 K. You may also want to reduce wscut. What is the estimated critical temperature with McMillan formula in your case?
Best, Roxana Dear Roxana, Thanks a lot for your kind reply. In my case, the Tc is very very low (e.g. using mu=0.05, the Tc is ~0.001 K). I know my system is not physically meaningful, I just want to test if the code can fit my systems for calculations. Now I guess I know where does the problem come from, following you comments above. Thanks a lot.

Tue Aug 21, 2018 6:46 am 



Page 1 of 1

[ 3 posts ] 

Who is online 
Users browsing this forum: No registered users and 4 guests 

You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum


